Gen 2 All in One 12V TRIO Flatmount
The Gen 2 All in One 12V TRIO Flatmount is a low profile mounting solution that includes everything you need to power your dish on 12V or 24V power! This allows you to eliminate the bulky and power hungry starlink router, and allows easy transfer of Gen 2 Starlink™ on vehicles in multiple locations without the setup time.
De-cased aftermarket router is enclosed within the case. Power saving is ~30% compared to using stock starlink router and added benefit is no longer needing to run a 12v-110v inverter.
Available as bare wire, cigarette lighter plug, or ring terminals
Voltage converter accepts 10-30V input
** All mounts now include a IP68 Hydrophobic pressure relief vent to equalize the pressure inside/outside the sealed enclosure and reduce condensation.
Install Video: TRIO Gen 2 Flatmount (pre-crimped cable is included so one only need to cut the dish and plug in the connector for the All in One 12V version)
Each of these TRIO Flatmounts is individually handcrafted in BC, Canada.
For additional info, see below.
The Gen 2 All in One 12V TRIO Flatmount is a low profile mounting solution that includes everything you need to power your dish on 12V or 24V power! This allows you to eliminate the bulky and power hungry starlink router, and allows easy transfer of Gen 2 Starlink™ on vehicles in multiple locations without the setup time.
De-cased aftermarket router is enclosed within the case. Power saving is ~30% compared to using stock starlink router and added benefit is no longer needing to run a 12v-110v inverter.
Available as bare wire, cigarette lighter plug, or ring terminals
Voltage converter accepts 10-30V input
** All mounts now include a IP68 Hydrophobic pressure relief vent to equalize the pressure inside/outside the sealed enclosure and reduce condensation.
Install Video: TRIO Gen 2 Flatmount (pre-crimped cable is included so one only need to cut the dish and plug in the connector for the All in One 12V version)
Each of these TRIO Flatmounts is individually handcrafted in BC, Canada.
For additional info, see below.
The Gen 2 All in One 12V TRIO Flatmount is a low profile mounting solution that includes everything you need to power your dish on 12V or 24V power! This allows you to eliminate the bulky and power hungry starlink router, and allows easy transfer of Gen 2 Starlink™ on vehicles in multiple locations without the setup time.
De-cased aftermarket router is enclosed within the case. Power saving is ~30% compared to using stock starlink router and added benefit is no longer needing to run a 12v-110v inverter.
Available as bare wire, cigarette lighter plug, or ring terminals
Voltage converter accepts 10-30V input
** All mounts now include a IP68 Hydrophobic pressure relief vent to equalize the pressure inside/outside the sealed enclosure and reduce condensation.
Install Video: TRIO Gen 2 Flatmount (pre-crimped cable is included so one only need to cut the dish and plug in the connector for the All in One 12V version)
Each of these TRIO Flatmounts is individually handcrafted in BC, Canada.
For additional info, see below.
-
3D printed from waterproof and UV resistant thermoplastic that will not warp
4 pieces are acetone welded together for near seamless and very strong joints
3mm acrylic base is adhered using sikaflex 221.
Brass heat set inserts ensure screws won’t loosen over time
EPDM O-ring gasket is compressed by 4.5 mm polycarbonate top with M5 SS hardware
*NOTE: due to the hands on assembly in the manufacturing process, there may be slight variations in textures and colors between mounts.
*All parts needed to complete the install are included in the kit, however you will need the following tools for DIY install:
Table saw, oscillating multitool, or dremel to cut apart the dish
RJ45 Passthrough crimp tool (available on amazon for $20)
3mm hex key/bit for tightening M5 stainless steel screws
Please Note: This is a DIY kit for those with basic tools and hands-on experience. If you'd like us to handle the conversion, select "Yes I will ship my Gen 2 Dish for install". We'll reach out to you via email to coordinate sending in your antenna and 75ft or 150ft network cable in. The Wi-Fi router and metal base are not needed for flat mount conversions. Do not include them in the shipment to us when sending in your antenna for modification. -
Overall Dimensions: 1.25"H x 13.55"W x 21.85"L
Color options: Black or White
Mounting options: Through-bolt, magnets, VHB adhesive, combination of VHB adhesive and magnets, suction cups, and tilting option for all the above. -
⚠ Using Starlink™ in motion may violate your Terms of Service depending on your service location. Consult your Terms of Service to determine if this applies to you.
⚠ All Gen 2 TRIO Flatmount kits require cutting the antenna dish apart to achieve a low profile. Modifying your Starlink™ antenna will void the warranty and is not endorsed or supported by Starlink™/SpaceX.
⚠ Modifying your dish with power tools comes with risk of damaging the circuitry. Do so at your own risk.
⚠ Given the varying conditions of surfaces this can be mounted to, it is ultimately up to the end user to make sure the antenna mount is sufficiently secured. By purchasing and using this product, you agree to waive any claims that you may have against TRIO Flatmount, www.trioflatmount.com, and included entities, from any and all liability for any loss, damage, expense or injury, including death, that may suffer as a result of the use of the product, due to any cause whatsoever.
Lead time: Orders are currently shipped out in 1-2 weeks. If you need something sooner please email us and we'll do our best to accommodate.
